Edge Bander, Cold Press & Panel Saw Installed in Andhra Pradesh
    Product Details

    Edge Bander, Cold Press & Panel Saw Installed in Andhra Pradesh

    Senbsen TeamNov 06, 20266 min read
    Edge Bander, Cold Press & Panel Saw Installed in Andhra Pradesh

    SENBSEN has successfully installed three woodworking machines for Mr. Sunil Kumar in Andhra Pradesh: an SBS-668-S automatic edge banding machine, an SCP48/60/1 60-ton hydraulic cold press, and a sliding table panel saw. Together, these three machines cover the core stages of panel furniture production — cutting, pressing and edge finishing — under one roof.

    Our technical team handled the complete setup on site, from installation and commissioning to hands-on operator training, so production could begin without delay.

    1. SENBSEN SBS-668-S Automatic Edge Banding Machine

    Edge Bander, Cold Press & Panel Saw Installed in Andhra Pradesh 2

    The SBS-668-S applies edge banding tape to the exposed edges of MDF, plywood and particle board, giving furniture panels a clean, finished look.

    Technical specifications

    • Minimum panel length: ≥120 mm

    • Minimum panel width: ≥40 mm

    • Panel thickness: 10–60 mm

    • Edge banding thickness: 0.4–2.0 mm

    • Feed rate: 18 / 20 / 22 m/min

    • Input voltage: 415V

    • Input frequency: 50 Hz

    • Air pressure: 0.6 MPa

    • Total power: Approx. 18.3 kW

    • Machine dimensions (L×W×H): 6000 × 900 × 1800 mm

    Functions and benefits

    • Edge banding application: Gives MDF, plywood and particle board panels a finished, durable edge.

    • Wide panel thickness range: Handles panels from 10 mm to 60 mm thick, suiting wardrobes, kitchens, office furniture and more.

    • Flexible tape thickness: Works with edge banding from 0.4 mm to 2.0 mm.

    • High-speed feeding: Three feed speeds — 18, 20 and 22 m/min — for efficient, high-volume production.

    • Industrial power supply: Runs on 415V, 50 Hz with approximately 18.3 kW total power.

    2. SENBSEN SCP48/60/1 60-Ton Hydraulic Cold Press

    The SCP48/60/1 is a 60-ton hydraulic cold press built for pressing and bonding wooden panels — laminating, veneering and making flush doors and board panels.

    Technical specifications

    • Model number: SCP48/60/1

    • Working area: 2500 × 1250 mm (customization available)

    • Maximum pressure: 60 ton

    • Maximum opening: 1000 mm

    • Installed power: 4 kW

    • Oil cylinders: Ø90 × 2 pcs

    • Machine weight: 2200 kg

    • Power supply: 415V, 50 Hz, 3 phase

    • Machine dimensions (L×W×H): 3000 × 1250 × 2500 mm

    Functions and benefits

    • 60-ton pressing force: Delivers strong, even pressure for reliable panel bonding.

    • Large working area: 2500 × 1250 mm fits full-size boards, with custom sizes available on request.

    • 1000 mm maximum opening: Leaves room to press stacks of panels in a single cycle.

    • Twin hydraulic cylinders: Two Ø90 mm oil cylinders spread pressure across the platen.

    • Low power draw: Only 4 kW installed power, keeping running costs low.

    3. SENBSEN Sliding Table Panel Saw

    The sliding table panel saw makes accurate, chip-free cuts on large wooden panels and boards, with a scoring blade and digital angle display.

    Technical specifications

    • Power supply: 415V, 3 phase, 50 Hz or customized

    • Main motor power: 6.5/5.5 kW / 7.5 HP*

    • Scoring spindle power: 1.1 kW

    • Sliding table length: 3200 mm

    • Sliding table width: 380 mm

    • Maximum cutting length: 3200 mm

    • Maximum cutting width: 1250 mm

    • Maximum cutting height: 80 mm

    • Main saw shaft diameter: Ø30 mm

    • Scoring saw shaft diameter: Ø20 mm

    • Main saw speed: 4500–6000 RPM

    • Scoring saw speed: 8000–9000 RPM

    • Saw blade angle: 0–45°

    • Angle display: Digital

    • Weight: 850 kg

    • Machine size: 2100 × 1100 × 1060 mm

    • Sliding table size: 3400 × 730 × 270 mm

    Functions and benefits

    • Full-sheet cutting: 3200 mm cutting length handles standard 8 × 4 ft boards in one pass.

    • Chip-free edges: The 1.1 kW scoring saw pre-cuts the laminate surface, preventing chipping on the bottom face.

    • Angle cutting: Blade tilts from 0° to 45°, with a digital display for precise bevel cuts.

    • Thick material capacity: Cuts up to 80 mm in height.

    • Stable, accurate operation: An 850 kg build reduces vibration for clean, square cuts.

    Professional Installation and Operator Training

    SENBSEN's service engineers completed the full installation at Mr. Sunil Kumar's facility, so all three machines were production-ready from day one.

    • Site check and positioning: Each machine was placed for a smooth flow from cutting to pressing to edge banding.

    • Electrical and pneumatic setup: 415V three-phase connections and the 0.6 MPa air supply for the edge bander were checked and connected.

    • Commissioning and trial runs: Every machine was calibrated and tested with live panels before handover.

    • Operator training: The customer's operators were trained hands-on in daily operation, safe working practices, and routine maintenance.

    • After-sales support: Our technical team stays available for service, spares and troubleshooting.

    Customer Feedback

    We purchased SENBSEN's machines and the installation was done properly. I liked their service.

    — Mr. Sunil Kumar, Andhra Pradesh

    Benefits for the Customer

    With cutting, pressing and edge banding now in-house, Mr. Sunil Kumar's unit can produce finished furniture panels without depending on outside job work.

    • Complete panel workflow: Boards are cut on the panel saw, bonded on the cold press, and finished on the edge bander — all in one facility.

    • Higher output: Feed speeds of up to 22 m/min on the edge bander and full-sheet cutting on the panel saw raise daily production.

    • Better finish quality: Scoring-saw cuts, even 60-ton pressing and machine-applied edge banding give a consistent, professional finish.

    • Flexibility across products: Panel thickness from 10 to 60 mm and edge tape from 0.4 to 2.0 mm cover kitchens, wardrobes, office and modular furniture.

    • Lower outsourcing costs: In-house processing cuts job-work charges and transport time.

    • Trained team from day one: Hands-on operator training means faster ramp-up and fewer errors.

    • Local service backing: SENBSEN's technical team supports the customer with service and spares.

    Frequently Asked Questions

    1. What panel thickness can the SENBSEN SBS-668-S edge banding machine handle?
      It processes panels from 10 mm to 60 mm thick, with edge banding tape from 0.4 mm to 2.0 mm.

    2. What is the feed speed of the SBS-668-S?
      It offers three feed speeds: 18, 20 and 22 metres per minute.

    3. Can the cold press working area be customized?
      Yes. The standard working area is 2500 × 1250 mm, and custom sizes are available on request.

    4. How much pressure does the SENBSEN cold press deliver?
      The SCP48/60/1 delivers up to 60 tons of pressure through two Ø90 mm hydraulic cylinders.

    5. Can the panel saw cut a full 8 × 4 ft board?
      Yes. It has a maximum cutting length of 3200 mm and a maximum cutting width of 1250 mm.

    6. What power supply do these machines need?
      All three machines run on a 415V, 50 Hz, three-phase supply. The edge bander also needs a 0.6 MPa compressed air supply.

    7. Does SENBSEN provide installation and training?
      Yes. Our engineers install and commission every machine on site and train your operators hands-on.

    8. Does SENBSEN supply machines in Andhra Pradesh?
      Yes. SENBSEN supplies, installs and services woodworking machinery for furniture manufacturers across India, including Andhra Pradesh.

    Planning Your Own Furniture Production Setup?

    Whether you need a single machine or a complete panel processing line, SENBSEN can help you choose, install and run the right equipment.

    • Phone: +91 87080 56233

    • Email: info@senbsen.in

    • Website: senbsen.in

    • Instagram: @senbsenindia

    • Address: Site No. 51, New Katha No. 89, Vaddarahalli Village, Bengaluru 562130